S-Plastics Geloy XTPM302 resin is a general purpose ASA/PC injection moulding grade, available in various colors.Typical properties measured on natural material.
TYPICAL PROPERTIES (1) | |||
MECHANICAL | Value | Unit | Standard |
Tensile Stress, yld, Type I, 50 mm/min | 55 | MPa | ASTM D 638 |
Tensile Stress, brk, Type I, 50 mm/min | 44 | MPa | ASTM D 638 |
Tensile Stress, yld, Type I, 5 mm/min | 51 | MPa | ASTM D 638 |
Tensile Stress, brk, Type I, 5 mm/min | 47 | MPa | ASTM D 638 |
Tensile Strain, yld, Type I, 50 mm/min | 3.7 | % | ASTM D 638 |
Tensile Strain, brk, Type I, 50 mm/min | 95 | % | ASTM D 638 |
Tensile Strain, yld, Type I, 5 mm/min | 3.6 | % | ASTM D 638 |
Tensile Strain, brk, Type I, 5 mm/min | >100 | % | ASTM D 638 |
Tensile Modulus, 5 mm/min | 2370 | MPa | ASTM D 638 |
Tensile Stress, yield, 5 mm/min | 49 | MPa | ISO 527 |
Tensile Stress, break, 5 mm/min | 43 | MPa | ISO 527 |
Tensile Stress, yield, 50 mm/min | 54 | MPa | ISO 527 |
Tensile Stress, break, 50 mm/min | 43 | MPa | ISO 527 |
Tensile Strain, yield, 5 mm/min | 3.3 | % | ISO 527 |
Tensile Strain, break, 5 mm/min | 80 | % | ISO 527 |
Tensile Strain, yield, 50 mm/min | 3.7 | % | ISO 527 |
Tensile Strain, break, 50 mm/min | 55 | % | ISO 527 |
Tensile Modulus, 1 mm/min | 2370 | MPa | ISO 527 |
Flexural Stress, yield, 2 mm/min | 80 | MPa | ISO 178 |
Flexural Modulus, 2 mm/min | 2300 | MPa | ISO 178 |
IMPACT | Value | Unit | Standard |
Izod Impact, notched, 23°C | 485 | J/m | ASTM D 256 |
Izod Impact, notched, 0°C | 285 | J/m | ASTM D 256 |
Izod Impact, notched, -10°C | 175 | J/m | ASTM D 256 |
Izod Impact, notched, -20°C | 140 | J/m | ASTM D 256 |
Izod Impact, notched, -30°C | 105 | J/m | ASTM D 256 |
Multiaxial Impact | 94 | J | ISO 6603 |
Izod Impact, notched 80*10*4 +23°C | 28 | kJ/m² | ISO 180/1A |
Izod Impact, notched 80*10*4 0°C | 15 | kJ/m² | ISO 180/1A |
Izod Impact, notched 80*10*4 -10°C | 11 | kJ/m² | ISO 180/1A |
Izod Impact, notched 80*10*4 -20°C | 7 | kJ/m² | ISO 180/1A |
Izod Impact, notched 80*10*4 -30°C | 6 | kJ/m² | ISO 180/1A |
Charpy 23°C, V-notch Edgew 80*10*4 sp=62mm | 38 | kJ/m² | ISO 179/1eA |
Charpy -30°C, V-notch Edgew 80*10*4 sp=62mm | 8 | kJ/m² | ISO 179/1eA |
Charpy 23°C, Unnotch Edgew 80*10*4 sp=62mm | NB | kJ/m² | ISO 179/1eU |
Charpy -30°C, Unnotch Edgew 80*10*4 sp=62mm | NB | kJ/m² | ISO 179/1eU |
THERMAL | Value | Unit | Standard |
CTE, -40°C to 40°C, flow | 9.5E-05 | 1/°C | ISO 11359-2 |
CTE, -40°C to 40°C, xflow | 9.5E-05 | 1/°C | ISO 11359-2 |
Ball Pressure Test, approximate maximum | 100 | °C | IEC 60695-10-2 |
Vicat Softening Temp, Rate A/50 | 116 | °C | ISO 306 |
Vicat Softening Temp, Rate B/50 | 103 | °C | ISO 306 |
Vicat Softening Temp, Rate B/120 | 104 | °C | ISO 306 |
HDT/Be, 0.45MPa Edgew 120*10*4 sp=100mm | 103 | °C | ISO 75/Be |
HDT/Ae, 1.8 MPa Edgew 120*10*4 sp=100mm | 87 | °C | ISO 75/Ae |
PHYSICAL | Value | Unit | Standard |
Mold Shrinkage on Tensile Bar, flow (2) | 0.4 - 0.6 | % | S-Plastics Method |
Density | 1.1 | g/cm³ | ISO 1183 |
Water Absorption, (23°C/sat) | 0.8 | % | ISO 62 |
Moisture Absorption (23°C / 50% RH) | 0.3 | % | ISO 62 |
Melt Volume Rate, MVR at 220°C/10.0 kg | 10 | cm³/10 min | ISO 1133 |
Melt Volume Rate, MVR at 240°C/5.0 kg | 10 | cm³/10 min | ISO 1133 |
Melt Volume Rate, MVR at 260°C/5.0 kg | 27 | cm³/10 min | ISO 1133 |
ELECTRICAL | Value | Unit | Standard |
Volume Resistivity | 2.5E+15 | Ohm-cm | ASTM D 257 |
Surface Resistivity | 1.9E+16 | Ohm | ASTM D 257 |
Dielectric Strength, in oil, 1.6 mm | 27.8 | kV/mm | ASTM D 149 |
Dissipation Factor, 1 MHz | 0.0175 | - | ASTM D 150 |
Source GMD, last updated:01/03/2005 |
Parameter | ||
Injection Molding | Value | Unit |
Drying Temperature | 90 - 100 | °C |
Drying Time | 2 - 4 | hrs |
Maximum Moisture Content | 0.02 | % |
Melt Temperature | 250 - 280 | °C |
Nozzle Temperature | 230 - 270 | °C |
Front - Zone 3 Temperature | 240 - 280 | °C |
Middle - Zone 2 Temperature | 230 - 270 | °C |
Rear - Zone 1 Temperature | 220 - 260 | °C |
Hopper Temperature | 60 - 80 | °C |
Mold Temperature | 50 - 80 | °C |
Source GMD, last updated:01/03/2005 |
Other related products we recommend:
Please contact us for specific quotations and more details.
Brand | Series | Model |
S-Plastics | Geloy | HRA222F-10000 |
HRA222F-7T2D242 | ||
XP4034-BK1041 | ||
XP4034-NA1000 | ||
XTPMFR10-WH9F029 |
.
In recent years, we have deeply cultivated the domestic market and actively explored foreign markets.Up to now, we have provided high-quality products and services to more than 1,000 customers in various industries, including: electronics and electrical appliances, medical, food, automotive electronics, optoelectronic communications, photovoltaic new energy, water treatment, transportation and other industries.
Samtion chemical supplies engineering plastics and special modified materials of S-Plastics and other brands.Our authentic products are guaranteed, with complete qualifications and superior supply capacity and price advantages.
Every batch of our products is subject to strict quality inspection to ensure the original supply. All products have MSDS, ROHS, SGS, REACH, FDA, EU, UL, COC / COA certificates!!
For more information please download the datesheet |
|
S-Plastics Geloy XTPM302.pdf |
Get The Latest Quotation
First-level distribution source in South China Reduce procurement costs, improve supply stability, Help you find the most suitable engineering plastic materials
Click to consult and get the latest quotation within 24 hours! |