S-Plastics Lexan ML3272 resin is a high viscosity grade especially developed for the extrusion of complex sheet and profiles. LEXAN ML3272 is used inapplications where a combination of high impact resistance and light transmission is required such as lighting, factory glazing and roofs.
MECHANICAL | Value | Unit | Standard |
Taber Abrasion, CS-17, 1 kg | 10 | mg/1000cy | S-Plastics Method |
Tensile Stress, yield, 50 mm/min | 60 | MPa | ISO 527 |
Tensile Stress, break, 50 mm/min | 55 | MPa | ISO 527 |
Tensile Strain, yield, 50 mm/min | 6 | % | ISO 527 |
Tensile Strain, break, 50 mm/min | 100 | % | ISO 527 |
Tensile Modulus, 1 mm/min | 2350 | MPa | ISO 527 |
Flexural Stress, yield, 2 mm/min | 95 | MPa | ISO 178 |
Flexural Modulus, 2 mm/min | 2300 | MPa | ISO 178 |
Hardness, H358/30 | 95 | MPa | ISO 2039-1 |
IMPACT | Value | Unit | Standard |
Izod Impact, unnotched 80*10*3 +23°C | NB | kJ/m² | ISO 180/1U |
Izod Impact, unnotched 80*10*3 -30°C | NB | kJ/m² | ISO 180/1U |
Izod Impact, notched 80*10*3 +23°C | 65 | kJ/m² | ISO 180/1A |
Izod Impact, notched 80*10*3 -30°C | 12 | kJ/m² | ISO 180/1A |
Charpy 23°C, V-notch Edgew 80*10*3 sp=62mm | 70 | kJ/m² | ISO 179/1eA |
Charpy -30°C, V-notch Edgew 80*10*3 sp=62mm | 13 | kJ/m² | ISO 179/1eA |
Charpy 23°C, Unnotch Edgew 80*10*3 sp=62mm | NB | kJ/m² | ISO 179/1eU |
Charpy -30°C, Unnotch Edgew 80*10*3 sp=62mm | NB | kJ/m² | ISO 179/1eU |
Charpy Impact, notched, 23°C | 30 | kJ/m² | ISO 179/2C |
THERMAL | Value | Unit | Standard |
Thermal Conductivity | 0.2 | W/m-°C | ISO 8302 |
CTE, 23°C to 80°C, flow | 7.E-05 | 1/°C | ISO 11359-2 |
Ball Pressure Test, 125°C +/- 2°C | PASSES | - | IEC 60695-10-2 |
Vicat Softening Temp, Rate A/50 | 148 | °C | ISO 306 |
Vicat Softening Temp, Rate B/50 | 146 | °C | ISO 306 |
Vicat Softening Temp, Rate B/120 | 148 | °C | ISO 306 |
HDT/Be, 0.45MPa Edgew 120*10*4 sp=100mm | 136 | °C | ISO 75/Be |
HDT/Ae, 1.8 MPa Edgew 120*10*4 sp=100mm | 124 | °C | ISO 75/Ae |
Relative Temp Index, Elec | 130 | °C | UL 746B |
Relative Temp Index, Mech w/impact | 125 | °C | UL 746B |
Relative Temp Index, Mech w/o impact | 125 | °C | UL 746B |
PHYSICAL | Value | Unit | Standard |
Mold Shrinkage on Tensile Bar, flow (2) | 0.5 - 0.7 | % | S-Plastics Method |
Density | 1.2 | g/cm³ | ISO 1183 |
Water Absorption, (23°C/sat) | 0.35 | % | ISO 62 |
Moisture Absorption (23°C / 50% RH) | 0.15 | % | ISO 62 |
Melt Volume Rate, MVR at 300°C/2.16 kg | 8 | cm³/10 min | ISO 1133 |
OPTICAL | Value | Unit | Standard |
Light Transmission | 88 - 89 | % | ASTM D 1003 |
Haze | 0.5 - 2 | % | ASTM D 1003 |
ELECTRICAL | Value | Unit | Standard |
Volume Resistivity | >1.E+15 | Ohm-cm | IEC 60093 |
Surface Resistivity, ROA | >1.E+15 | Ohm | IEC 60093 |
Dielectric Strength, in oil, 3.2 mm | 17 | kV/mm | IEC 60243-1 |
Relative Permittivity, 50/60 Hz | 2.7 | - | IEC 60250 |
Relative Permittivity, 1 MHz | 2.7 | - | IEC 60250 |
Dissipation Factor, 50/60 Hz | 0.001 | - | IEC 60250 |
Dissipation Factor, 1 MHz | 0.01 | - | IEC 60250 |
FLAME CHARACTERISTICS | Value | Unit | Standard |
UL Recognized, 94HB Flame Class Rating (3) | 0.75 | mm | UL 94 |
UL Recognized, 94HB Flame Class Rating 2nd value (3) | 3 | mm | UL 94 |
Oxygen Index (LOI) | 25 | % | ISO 4589 |
Source GMD, last updated:01/12/1990 |
Profile Extrusion | Value | Unit |
Drying Temperature | 120 | °C |
Drying Time | 2 - 4 | hrs |
Melt Temperature | 280 - 300 | °C |
Barrel - Zone 1 Temperature | 240 - 280 | °C |
Barrel - Zone 2 Temperature | 260 - 290 | °C |
Barrel - Zone 3 Temperature | 260 - 290 | °C |
Barrel - Zone 4 Temperature | 260 - 290 | °C |
Hopper Temperature | 100 - 120 | °C |
Adapter Temperature | 270 - 300 | °C |
Die Temperature | 260 - 290 | °C |
Calibrator Temperature | 80 - 100 | °C |
Source GMD, last updated:01/12/1990 | ||
THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES. | ||
PLEASE CHECK WITH YOUR (LOCAL SALES OFFICE) FOR AVAILABILITY IN YOUR REGION | ||
(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294. |
||
(2) Only typical data for selection purposes. Not to be used for part or tool design. | ||
(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions. | ||
(4) Internal measurements according to UL standards. |
For more information please download the datasheet |
|
![]() |
S-Plastics Lexan ML3272.pdf |
Get The Latest Quotation
First-level distribution source in South China Reduce procurement costs, improve supply stability, Help you find the most suitable engineering plastic materials
|
|